Juniper인증 JN0-532시험을 패스하고 싶다면ITExamDump에서 출시한Juniper인증 JN0-532덤프가 필수이겠죠. Juniper인증 JN0-532시험을 통과하여 원하는 자격증을 취득하시면 회사에서 자기만의 위치를 단단하게 하여 인정을 받을수 있습니다.이 점이 바로 많은 IT인사들이Juniper인증 JN0-532시험에 도전하는 원인이 아닐가 싶습니다. ITExamDump에서 출시한Juniper인증 JN0-532덤프 실제시험의 거의 모든 문제를 커버하고 있어 최고의 인기와 사랑을 받고 있습니다. 어느사이트의Juniper인증 JN0-532공부자료도ITExamDump제품을 대체할수 없습니다.학원등록 필요없이 다른 공부자료 필요없이 덤프에 있는 문제만 완벽하게 공부하신다면Juniper인증 JN0-532시험패스가 어렵지 않고 자격증취득이 쉬워집니다.
ITExamDump는 여러분의 요구를 만족시켜드리는 사이트입니다. 많은 분들이 우리사이트의 it인증덤프를 사용함으로 관련it시험을 안전하게 패스를 하였습니다. 이니 우리 ITExamDump사이트의 단골이 되었죠. ITExamDump에서는 최신의Juniper JN0-532자료를 제공하며 여러분의Juniper JN0-532인증시험에 많은 도움이 될 것입니다.
Juniper인증 JN0-532시험은 IT인증자격증중 가장 인기있는 자격증을 취득하는 필수시험 과목입니다. Juniper인증 JN0-532시험을 패스해야만 자격증 취득이 가능합니다. ITExamDump의Juniper인증 JN0-532는 최신 시험문제 커버율이 높아 시험패스가 아주 간단합니다. Juniper인증 JN0-532덤프만 공부하시면 아무런 우려없이 시험 보셔도 됩니다. 시험합격하면 좋은 소식 전해주세요.
Juniper인증 JN0-532시험에 도전하고 싶으시다면 최강 시험패스율로 유명한ITExamDump의 Juniper인증 JN0-532덤프로 시험공부를 해보세요. 시간절약은 물론이고 가격도 착해서 간단한 시험패스에 딱 좋은 선택입니다. Juniper 인증JN0-532시험출제경향을 퍼펙트하게 연구하여ITExamDump에서는Juniper 인증JN0-532시험대비덤프를 출시하였습니다. ITExamDump제품은 고객님의 IT자격증 취득의 앞길을 훤히 비추어드립니다.
한번에Juniper인증JN0-532시험을 패스하고 싶으시다면 완전 페펙트한 준비가 필요합니다. 완벽한 관연 지식터득은 물론입니다. 우리ITExamDump의 자료들은 여러분의 이런 시험준비에 많은 도움이 될 것입니다.
Juniper인증 JN0-532시험패스는 고객님의 IT업계종사자로서의 전환점이 될수 있습니다.자격증을 취득하여 승진 혹은 연봉협상 방면에서 자신만의 위치를 지키고 더욱 멋진 IT인사로 거듭날수 있도록 고고싱할수 있습니다. ITExamDump의 Juniper인증 JN0-532덤프는 시장에서 가장 최신버전으로서 시험패스를 보장해드립니다.
시험 번호/코드: JN0-532
시험 이름: Juniper (FWV,Specialist (JNCIS -FWV))
ITExamDump의Juniper JN0-532시험자료의 문제와 답이 실제시험의 문제와 답과 아주 비슷합니다. 우리의 짧은 학습가이드로 빠른 시일 내에 관련지식을 터득하여 응시준비를 하게 합니다. 우리는 우리의Juniper JN0-532인증시험덤프로 시험패스를 보장합니다.
JN0-532 덤프무료샘플다운로드하기: http://www.itexamdump.com/JN0-532.html
NO.1 Which three statements are true regarding IKE Phase 1? (Choose three.)
A.Placing the SA proposal list in message 1 is an option.
B.The digital certificate is used to decrypt the session key.
C.The DH key exchange is used to validate the session key.
D.The DH key exchange and digital certificates are both optional.
E.The proxy-id is used to determine which SA is referenced for the VPN.
Answer: ABC
Juniper JN0-532기출문제 JN0-532기출문제
NO.2 Click the Exhibit button.
In the exhibit, what is the source IP address of the multicast traffic?
A.236.1.1.1
B.10.10.10.1
C.20.20.20.10
D.20.20.20.200
Answer: B
Juniper시험문제 JN0-532자격증 JN0-532인증 JN0-532덤프
NO.3 What must be enabled to protect Phase 2 key exchanges?
A.Phase 1 PFS
B.Phase 2 SHA
C.Phase 2 3-DES
D.Phase 2 DH key exchange tiations? (Choose two.)
A.proxy-id, SA proposal list
B.IKE cookie, SA proposal list
C.hash [ID + Key], DH key exchange
D.SA proposal list, optional DH key exchange
Answer: D
Juniper JN0-532 JN0-532최신덤프 JN0-532
NO.4 You have entered the command set ffilter src-ip 1.1.7.250 dst-ip 10.1.10.5 ip-prot 6
What will be the resulting output in the debug for which this was created?
A.If the packet has a src-ip of 1.1.7.250 or a dst-ip of 10.1.10.5 or has TCP as its protocol then it will be
captured
B.If the packet has a src-ip of 1.1.7.250 or a dst-ip of 10.1.10.5 or has UDP as its protocol then it will be
captured
C.If the packet has a src-ip of 1.1.7.250 and a dst-ip of 10.1.10.5 and has TCP as its protocol then it will
be captured
D.If the packet has a src-ip of 1.1.7.250 and a dst-ip of 10.1.10.5 and has UDP as its protocol then it will
be captured
Answer: C
Juniper pdf JN0-532기출문제 JN0-532
NO.5 Click the Exhibit button.
Review the exhibit. Track-ip has failed on the device, but the device did not fail over to the second unit in
the cluster:
Why has failover not occurred?
A.The physical interfaces have not failed.
B.The track-ip interval is not sufficient to cause failover.
C.The track-ip address weight is not sufficient to cause failover.
D.The track-ip address threshold is not sufficient to cause failover.
Answer: C
Juniper JN0-532시험문제 JN0-532
NO.6 Which command is used to verify that IGMP is running correctly?
A.get route igmp
B.get igmp query
C.set igmp query interface e0/1
D.exec igmp interface e0/1 query
Answer: D
Juniper JN0-532 JN0-532 JN0-532
NO.7 Which two item pairs are exchanged during Phase 2 negotiations? (Choose two.)
A.proxy-id, SA proposal list
B.IKE cookie, SA proposal list
C.hash [ID + Key], DH key exchange
D.SA proposal list, optional DH key exchange
Answer: AD
Juniper dump JN0-532 JN0-532
NO.8 Which CLI command identifies the multicast sources visible to your ScreenOS device?
A.get route pim
B.get igmp source all
C.exec pim interface all query
D.get vrouter trust-vr protocol pim
Answer: D
Juniper JN0-532 dump JN0-532시험문제 JN0-532 dumps
NO.9 To which three ScreenOS components can a policy-based routing policy be bound? (Choose three.)
A.zone
B.policy
C.interface
D.virtual router
E.virtual system
Answer: ACD
Juniper JN0-532최신덤프 JN0-532최신덤프
NO.10 You have created a virtual router called VSYSA-vr and made it shareable. You then create the VSYS
using the WebUI, telling it to use an existing VR and selecting the VR called VSYSA-vr.
What is the status of the virtual router after you create the VSYS?
A.The router will be the default router but will no longer be shared.
B.The router will be the default router and will still have a shareable status.
C.The system will not let you use a shared virtual router when you create a new VSYS. The initial virtual
router must be private.
D.The system will not create a private vr for the VSYS but will assign the untrust-vr as the default router.
The shared Virtual router will not be the default router.
Answer: B
Juniper인증 JN0-532 JN0-532 dump JN0-532 JN0-532덤프
NO.11 During main mode negations a failure has occurred while using IKE certificates.
Which message pair would you review to troubleshoot this failure?
A.messages 1 & 2
B.messages 2 & 3
C.messages 3 & 4
D.messages 5 & 6
Answer: D
Juniper JN0-532 JN0-532덤프 JN0-532시험문제 JN0-532 dumps
NO.12 You have configured the following on your device.
set address trust MyPC 10.1.1.5/32
set address untrust CorpNet 10.10.0.0/16
set policy from trust to untrust MyPC CorpNet any permit
set int tunnel.1 zone untrust
set int tunnel.1 ip unnumbered int bgroup1
set ike gateway GW address 1.1.1.1 outgoing-interface e0/1 preshare Secret sec-level standard
set vpn VPN gateway GW sec-level standard
The tunnel interface is down, so the VPN cannot function properly. What is the problem?
A.The policy needs to have the action tunnel.
B.The VPN needs to be bound to the tunnel interface.
C.The tunnel interface needs to be placed in the trust zone.
D.The tunnel interface needs to be associated with the interface in the untrust zone.
Answer: B
Juniper JN0-532시험문제 JN0-532 dump JN0-532 pdf
NO.13 Which three OSPF parameters are interface parameters? (Choose three.)
A.cost
B.priority
C.neighbor list
D.summarization
E.advertise default route
Answer: ABC
Juniper자격증 JN0-532 JN0-532 JN0-532
NO.14 Click the Exhibit button.
In the exhibit, what is the address of the multicast receiver?
A.234.9.8.42
B.192.168.10.2
C.192.168.20.10
D.192.168.20.200
Answer: D
Juniper JN0-532최신덤프 JN0-532 JN0-532최신덤프
NO.15 Review the exhibit.
You've been asked to build a route-based hub and spoke network, with policy control for traffic travelling
from spoke to spoke. Which two of the following configuration options will meet this requirement?
(Choose two.)
A.Place the spoke tunnel interfaces in the trust zone and create policies on the spokes.
B.Place the spoke tunnel interfaces in the untrust zone and create policies on the spokes.
C.Create a single tunnel interface in the trust zone at the hub and enable intra-zone blocking.
D.Create separate tunnel interfaces at the hub and place them in different zones, then create policies at
the hub.
Answer: BD
Juniper인증 JN0-532인증 JN0-532자격증 JN0-532
NO.16 What must be configured differently for a route-based VPN and a policy-based VPN?
A.proxy-id
B.proposals
C.remote gateway type
D.binding the tunnel interface
Answer: D
Juniper JN0-532 JN0-532인증 JN0-532 pdf JN0-532 JN0-532
NO.17 Review the exhibit.
Which two of the following elements must be configured on the ScreenOS device in order to support
PIM-SM? (Choose two)
A.A multicast control policy
B.A bootstrap router process
C.A unicast routing protocol
D.A static RP
Answer: AC
Juniper JN0-532기출문제 JN0-532 JN0-532 dumps
NO.18 Which ScreenOS CLI command is necessary for configuring IGMP on interface ethernet0/1?
A.set igmp interface ethernet0/1
B.set multicast interface ethernet0/1
C.set interface ethernet0/1 igmp router
D.set igmp interface ethernet0/1 enable
Answer: C
Juniper dump JN0-532 JN0-532자료 JN0-532기출문제
NO.19 Click the Exhibit button.
In the exhibit, which two can be determined about the VPN? (Choose two.)
A.NAT-traversal is enabled.
B.The rekey interval is 8 hours.
C.This device initiated the Phase 1 negotiations.
D.The certificate used in this exchange is set to never expire.
Answer: BC
Juniper dumps JN0-532 JN0-532 JN0-532덤프
NO.20 Click the Exhibit button.
In the exhibit, the firewall administrator at the Storefront is complaining that when the communication to
the DataCenter1 fails, the preexisting transfers and applications are dropped when the traffic is switched
to DataCenter2.
Which statement explains this behavior?
A.SYN checking is enabled in the tunnel.
B.The weight value for the DataCenter2 is too high.
C.VPN monitor is misconfigured in the DataCenter2.
D.Phase 1 and Phase 2 negotiations to DataCenter2 did not occur on time.
Answer: A
Juniper JN0-532 JN0-532덤프 JN0-532 dumps
Juniper인증 JN0-532시험을 패스하는 지름길은ITExamDump에서 연구제작한 Juniper 인증JN0-532시험대비 덤프를 마련하여 충분한 시험준비를 하는것입니다. 덤프는 Juniper 인증JN0-532시험의 모든 범위가 포함되어 있어 시험적중율이 높습니다. Juniper 인증JN0-532시험패는 바로 눈앞에 있습니다. 링크를 클릭하시고ITExamDump의Juniper 인증JN0-532시험대비 덤프를 장바구니에 담고 결제마친후 덤프를 받아 공부하는것입니다.
댓글 없음:
댓글 쓰기